T300 PRO 2-in-1 OBD II Scanner + Battery Tester

A comprehensive 2-in-1 diagnostic tool combining OBD II scanning with advanced battery diagnostics. Supports cloud printing, customized shortcut keys, and 14 languages. Compatible with 97% of OBD II compliant vehicles with a 930mm OBD cable for easier reach.

Key Functions

• Read DTC– Read stored, pending, and permanent diagnostic trouble codes
• Clear DTC– Erase trouble codes and reset engine fault light
• Battery Life Detection– Comprehensive battery health analysis with SOH%, CCA, voltage, and impedance
• I/M Readiness– Check emission system readiness status via dedicated shortcut key
• ECU Info– Read vehicle ECU information and VIN
• Live Data– View 27+ real-time data parameters with recording and playback
• Mode 6– In-vehicle monitoring test for specific component tests
• O2 Sensor– Oxygen sensor performance testing
• Mode 8– Control of on-board system, test, or component
• Freeze Frame– Capture sensor data at the moment a fault is detected
• Online Software Upgrade– Update via Type-C connection from PC
• Cloud Printing– Scan QR code to view and share diagnostic reports as PDF
• 50,000+ Trouble Codes– Built-in DTC lookup for quick fault code definitions
• Vehicle Year Reading– Identify vehicle production year from VIN
• OBD Voltage Detection– Check OBD pin voltages to diagnose communication issues
• Data Stream Recording– Record and playback live data streams
• Customized Shortcuts– Assign F1/F2 keys to frequently used functions

Battery Diagnostics

Supports multiple battery test standards: CCA, JIS, GB, SAE, MCA, CA, DIN, IEC, EN, BCI. Battery range: 10AH–300AH, CCA scope: 20–2000 CCA.

Multiple detection modes:

• Standard Test– Shows SOH%, voltage, rated CCA, actual CCA, impedance, and battery power percentage
• Startup Test– Monitors voltage during engine cranking (CUR, MIN, MAX values)
• Charging Test– Verifies alternator output (load voltage, no-load voltage, voltage fluctuation)
• Voltage Waveform Monitoring– Monitor voltage waveform patterns
• Load Test– Tests battery under load conditions

Applicable battery types: ordinary lead-acid batteries, AGM flat batteries, AGM wound batteries, GEL gel batteries, EFB liquid-rich batteries.

Wide Range of Applications

The T300 PRO is suitable for vehicle types including: cars, trucks, passenger vehicles, diesel vehicles, motorcycles, boats, beach bikes and more.

Reading Vehicle Information

Automatic scanning connection — no need to manually select the brand or model. Reads VIN and identifies vehicle production year. Supports up to 9 different protocols for multiple vehicle brands:

1. SAE J1850 PWM (41.6 Kbaud)
2. SAE J1850 VPW (10.4 Kbaud)
3. ISO9141-2 (5 baud init, 10.4 Kbaud)
4. ISO15765-4 CAN (11 bit ID, 500 Kbaud)
5. ISO15765-4 CAN (29 bit ID, 500 Kbaud)
6. ISO15765-4 CAN (11 bit ID, 250 Kbaud)
7. ISO15765-4 CAN (29 bit ID, 250 Kbaud)
8. ISO14230-4 KWP (fast init, 10.4 Kbaud)
9. ISO14230-4 KWP (5 baud init, 10.4 Kbaud)

Real-Time Data View

View 27+ real-time car data parameters at a glance, including: Numbers of DTCs, Fuel system A/B status, Calculated load value, Engine coolant temperature, Short/Long term fuel trim, Inlet Pressure, Engine Speed, Engine Water Temperature, Ignition advance angle, and more. Supports Review Data, Record Data, Playback Data, and Unit of Measure settings.

Engine Troubleshooting

Quickly read the car's faults and clear the engine fault light. OBD menu includes: Read DTC, Clear DTC, I/M Status, ECU Info, Live Data, Mode 6, O2 Sensor, Mode 8, Freeze Frame. LED indicators provide instant status: Green = No fault codes; Yellow = Pending DTCs present; Red = One or more problems exist.

Built-in 50,000+ Fault Codes

Quick lookup of fault code definitions with an easy-to-use DTC Lookup interface. Navigate using directional keys to enter any DTC code for instant definition.

I/M Testing

The I/M Status function checks the operation of the emission system on OBD II-compliant vehicles. Accessible via the dedicated I/M shortcut key for one-touch access. Displays readiness status for MIS, FUEL, CCM, CAT, HCAT, EVAP, AIR, O2S, HRT, EGR monitors for both "This driving cycle" and "Since DTCs cleared" conditions.

In-Vehicle Monitoring Test (Mode 6)

After repairing or clearing fault codes, the on-board monitor test allows access to specific component tests. The vehicle manufacturer assigns MIDs and CIDs for testing different systems and components, including exhaust gas sensor monitors with test values, min/max limits, and status.

OBD Voltage

When the vehicle appears unable to diagnose, the OBD voltage function checks the voltage of OBD pins to help find vehicle faults faster. Displays voltage and normal range for: BUS+(2Pin), CAN-H(6Pin), K-line(7Pin), BUS-(10Pin), CAN-L(14Pin), line(15Pin), VIN(16Pin).

Customized Shortcuts

Assign the F1 and F2 shortcut keys to the most commonly used functions. Available functions include: Read DTC, Clear DTC, IM Status, ECU info, Live Data, Mode 6, O2 Sensor, Mode 8, Freeze, Voltage waveform monitoring, I/M.

Connection Method

OBD II Scanning:Find the DLC port and connect the OBD cable to the car DLC.

Battery Diagnostics:Connect the OBD connection cable to the clamp cable; connect the red clip to the positive battery terminal and the black clip to the negative battery terminal.

Build Quality

• Left and right silicone anti-slip design
• Pure copper core OBD cable for faster data transmission
• Soft rubber buttons for comfortable operation
• ABS housing for ruggedness and durability
• OBD cable length: 930mm (longer than typical 700mm cables)

Multi-Language Support

Interface available in 14 languages: English, Spanish, French, Italian, Russian, Portuguese, German, Polish, Dutch, Japanese, Turkish, Indonesian, Thai, Chinese. Also supports custom languages.

Product Parameters